Drilling Performance of AISI 430 Stainless Steel Using Al-Ti-N Coated and Uncoated HSS Drill Bits
Downloads
This study investigates the influence of tool coating and cutting parameters on the surface integrity and dimensional accuracy during drilling of ferritic stainless steel AISI 430. Using both Al-Ti-N coated and uncoated HSS drill bits, experiments were performed under dry conditions with varying spindle speeds (800–1200 rpm) and feed rates (0.1–0.2 mm/rev). Results show that coated tools consistently yielded lower surface roughness (Ra), reduced diameter error, improved hole roundness (ovality), and better perpendicularity. The Al-Ti-N coating significantly mitigated tool wear and thermal effects, enhancing process stability and microhardness near the drilled surface. Optimal drilling performance was observed at lower feed rates and moderate spindle speeds when using coated tools. These findings highlight the critical role of tool coatings and parameter optimization in machining ferritic stainless steels for high-precision applications.
Mohammed Mushtaq, B. Ramesh, “ A novel investigation on effect of process parameters on surface roughness while drilling normalized and annealed SAE 304 stainless steel and comparing the outputs with untreated stainless steel”, Materials Today: Proceedings, 2022
Abdiel M. Vilanova ⇑, Guilherme S. Vaz, André J. Souza, Émerson S. Passari, “Comparative study of drilling super austenitic stainless steel with external applications of reduced quantity nanofluid and flooded biolubricant”, Materials Today: Proceedings ,xxxx
V. Vignesh ⇑, Sandeep Satish, Vivek Gopi, J. Jishnoop, Gokul A. Menon, “ Comparison of coated and uncoated HSS drill bit on surface roughness material removal rate and dimensional accuracy of SS410 stainless steel”, Materials Today: Proceedings, 2022.
Marzouk a, Ahmad Aljabr b, Fahad Awjah Almehmadi c, Tabish Alam, ”Dynamic thermal analysis and drill bit temperature in AISI 430 stainless steel S.A.”, Thermal Science and Engineering Progress, 2024.
Lukas Pelikan, Michal Slaný,, Ondrej Stranský, , Libor Beranek,, Zdenek Pitrmuc,Lenka ˇCepova ,Stepanka Dvorackova, “Novel drill geometries for dry drilling of stainless steel “,Journal of Manufacturing Processes, 2023
C. Manickam ⇑, N Parthipan, ”Optimization of drilling parameters in AISI SS317L stainless steel material using Taguchi methodology”, Materials Today: Proceedings, 2020.
Lukas Schnellera, Manuel Henna, Christoph Spurkc, Alexander Olowinskyd, Felix Beckmanne, Julian Moosmanne, Daniel Holdera, Christian Hagenlochera, Thomas Grafa,”High-speed X-ray imaging of bulge formation during laser percussion drilling with various polarizations in stainless steel”, Procedia CIRP, (2024)
Yue Zhang, Xiuli He, Gang Yu , Shaoxia Li, Chongxi Tian , Weijian Ning,Yanmei Zhang,, “Dynamic evolution of keyhole during multi-pulse drilling with a millisecond laser on 304 stainless steel”, Optics & Laser Technology, (2022)
Chandra Nath , Lili Zheng, “Effect of In-Built Anisotropic and Heterogeneous Material Properties on Machinability in Drilling of AISI 304 Stainless Steel”, Journal of Manufacturing Processes (2020)
Guang-Hui Wang, Yue-Qiu Jiang, Ce-An Guo, “Effect of Nitrogen Content on the Corrosion Resistance of High-nitrogen Austenitic Stainless Steel for Nonmagnetic Drill Collar in a Harsh Service Environment”, International Journal of ELECTROCHEMICAL SCIENCE, 2022.
Amrit Pal, Sukhpal Singh Chatha, Hazoor Singh Sidhu, “Experimental investigation on the performance of MQL drilling of AISI 321 stainless steel using nano-graphene enhanced vegetable-oil-based cutting fluid”, Tribology International, 2020
Hailong Zhang, Yang Mao, Min Kang, Chenbin Ma, Hao Li, Yongnian Zhang, Xingsheng Wang, “Fabrication of high aspect ratio micro-holes on 304 stainless steel via backside-water-assisted laser drilling”, Optics and Lasers in Engineering, 2023.
Rabiae Arifa, Guillaume Fromentina, Frédéric Rossia, Bertrand Marcona, ”Investigations on drilling performance of high resistant austenitic stainless steel”, Journal of Manufacturing Processes, 2020.
Mohamed Akram Mechter, Mina Gadour,Lea Romain, Oguzhan Tuysuz, Myriam Brochu, ”Microstructural and fatigue characterization of 316L stainless steel”, Engineering Failure Analysis, 2024.
K. Balaji, M. Siva Kumar, N. Yuvaraj, “Multi objective taguchi–grey relational analysis and krill herd algorithm approaches to investigate the parametric optimization in abrasive water jet drilling of stainless steel”, Applied Soft Computing Journal, (2021).
Zehui Gu , Yuyang He *, Jinghu Ji , Yonghong Fu, ”Numerical simulation and experimental study of the shape variation influence on stainless steel drilling with picosecond laser”, Optics & Laser Technology, (2025).
C. Manickam ⇑, N. Parthipan, “Optimization of drilling parameters in AISI SS317L stainless steel material using Taguchi methodology”, Materials Today: Proceedings, (2020).
Amrit Pal, Sukhpal Singh Chatha, Hazoor Singh Sidhu,” Performance evaluation of the minimum quantity lubrication with Al2O3- mixed vegetable-oil-based cutting fluid in drilling of AISI 321 stainless steel”, Journal of Manufacturing Processes, (2021).
Houxiao Wang ∗, Xinmin Dai, Ye Xu, Jiao Liu, Jiaxin Shan, Naifei Ren, Xudong Ren, ”Real-time observation with metallurgical examination for laser percussion drilling in stainless steel sheets using simultaneous magnetic-ultrasonic assistance”, Optics Communications (2021).
V. Vignesh, S. Ilangovan, N. Radhika, “Statistical analysis of process parameters in drilling of SS410 stainless steel”, Materials Today: Proceedings, (2021).
