Studying the Effect of Rifling Parameters on the Stress State in a Gun Barrel Wall When Firing
Downloads
The problem of determining the stress state of the rifled-bore barrel when firing was presented in this article. Where the effects of rifling parameters such as the quantity of grooves n, groove width a, depth of groove t, radius of groove corner ρ were investigated. A rifled-bore barrel has been modeled and investigated by using Ansys software on the basis of finite element method. The problem has only been treated under pressure load in static case. The article can be used for reference to improve the accuracy in calculating design and manufacturing gun barrel.
Khong Dinh Tuy et al., Artillery system design base, Military Technical Academy, 2009 (in Vietnamese).
Phan Nguyen Thieu, Khong Dinh Tuy, Design principles of barreled weapons, People's Army Publishing House, 2000 (in Vietnamese).
Orlov B.V., Design of rocket and barreled systems, Mechanical engineering, Moscow, 1974 (in Rusian).
Chuev Yu.V. , Design of barreled complex, Mechanical engineering, Moscow, 1976 (in Rusian).
Lavit I.M., Tolokonnikov L.A., Low-cycle fatigue of hollow cylinders loaded with internal pressure, Izv. TulGU, Problems of special engineering, 1997, Issue 1, pp. 124-128 (in Rusian).
Ge Shuqiang et al., Strength and Modal Analysis of a Gun Barrel under Four Different Strength Theories, International Symposium on Advanced Launch Technologies (ISALT 2022), Journal of Physics: Conference Series, 2023, doi:10.1088/1742-6596/2460/1/012058
Yuzhao Yang et al., Dynamic stress analysis of anisotropic gun barrel under coupled thermo-mechanical loads via finite element method, Latin American Journal of Solids and Structures, 2020, 17(1), e243, https://doi.org/10.1590/1679-78255800
Junyu Chen et al., Thermo-mechanical analysis of strength degradation of 30SiMn2MoVA gun barrel material during continuous shooting, Engineering Failure Analysis, Volume 139, 2022, https://doi.org/10.1016/j.engfailanal.2022.106438
Abdullah Şentürk, Halil Işık, Celal Evci, Thermo-mechanically coupled thermal and stress analysis of interior ballistics problem, International Journal of Thermal Sciences, Volume 104, 2016, pp. 39-53, https://doi.org/10.1016/j.ijthermalsci.2015.12.019
Bui Quy Viet, Research on stress state of cannon barrel with spiral groove when firing, Vietnam Mechanics Journal, 2014 (in Vietnamese).
Q. Ma, C. Levy, M. Perl, Stress Concentration and Stress Intensity for Pressurized Eroded Autofrettaged Thick Cylinders With Bauschinger Effect , ASME 2010 Pressure Vessels and Piping Division/K-PVP Conference, 2010, https://doi.org/10.1115/PVP2010-25607
Leslie Banks-Sills, R. Eliasi, Fatigue life analysis of a cannon barrel, Engineering Failure Analysis, Volume 6, Issue 6, 1999, pp. 371-385, https://doi.org/10.1016/S1350-6307(98)00054-5
Chao-bin Hu, Xiao-bing Zhang, Influence of multiple structural parameters on interior ballistics based on orthogonal test methods, Defence Technology, Volume 15, Issue 5, 2019, pp. 690-697, https://doi.org/10.1016/j.dt.2019.06.014
Junping Gu et al., Geometry optimization for supercritical water heat transfer enhancement in non-uniformly heated rifled tubes, Applied Thermal Engineering, Volume 187, 2021, https://doi.org/10.1016/j.applthermaleng.2021.116566
Jia Sun et al., Analysis of gun barrel rifling twist, AIP Conference Proceedings, 2017, https://doi.org/10.1063/1.4982461
Hoang Xuan Luong et al., The theory of elasticity - plasticity – creep, Military Technical Academy, 2008 (in Vietnamese).
Zienkiewicz O.C., Taylor R.L., The finite element method. Oxford: Buttenworth, Heinemann, 2000.
Krukova N.V., Lavit I.M., The finite-element method in linear fracture mechanics problems // Proceedings of 3rd European Conference on Computational Mechanics, Lisbon: ECCM ,CD-ROM Proc, 2006.
Morozov E.M., Muizemnek A.Yu., Shadsky A.S., Ansys in the hands of an engineer: Fracture mechanics, Lenand, Moscow, 2008 (in Rusian).
Laham S.Al., Stress Intensity Factor and Limit Load Handbook, British Energy Generation Ltd, United Kingdom, 1999.
